Fatigue Behaviour of Metal Matrix Composites

Abstract

Abstract: Based mainly on the work done at the authors' laboratory in recent years,this paper examines what is currently known about the cyclic deformation and fatigue properties of metal matrix composites, with particular emphasis on discontinuous fiber (whisker or particulate)-reinforced Al composites. The following items are discussed:fatigue strength and life,cyclic deformation and microstructural evolution,microcrack initiation and growth,fatigue crack propagation behaviour.

Key words: metal matrix composite, cyclic deformation and fatigue, interfacial effect, crack-trapping and bridging

WANG Zhongguang SUN Zhengming YU Weicheng ** State Key Laboratory for Fatigue and Fracture of Materials,Institute of Metal Research,Academia Sinica,Shenyang.110015,China+ To whom correspondence should be addressed. Fatigue Behaviour of Metal Matrix Composites[J]. J Mater Sci Technol, 1992, 8(4): 235-248.

References

(1) A.P.Divecha,S.G.Fishman and S.D.Karmarker:J.Met.,1981,9,12．
(2) D.L.McDanels:Metall.Trans.,1985,16A,1105．
(3) S.V.Nair,J.K.Tien and R.C.Bater:Int.Metal Rev.,1985,30,275．
(4) LI Chenggong:J.Aeronautical Mater.,1990,10,145． (in Chinese)
(5) “Mechanical Properties and Failure Mechanisms of Metal Matrix Composites”,Research Report,State Key Laboratory for Fatigue and Fracture of Materials,Institute of Metal Research,Academia Sinica,Shenyang,China,1991． (in Chinese)
(6) D.F.Hassen,C.R.Crowe,J.S.Ahearn and D.C.Cooke:in Proc.on Failure Mechanisms in High Performance Materials,eds.J.G.Early,T.Robert Shives and J.H.Smith,1984,147．
(7) LIU Jun,YU Weicheng,WANG Zhongguang,WANG Dezun and YAO Zhongkai:in 7th National Conf.on Composite Materials.1992,Dalian,China.(in Chinese)
(8) LIU Jun:Master Degree Thesis,1991,Harbin Institute of Technology,Harbin,China(in Chinese)
(9) WANG Jian:Master Degree Thesis,1991,In- stitute of Metal Research,Academia Sinica.Shenyang,China.(in Chinese)
(10) D.R.Williams and M,E,Fine:in Proc.5th Int.Conf.on Composite Materials,eds.,W.C.Harrigan,Jr.,J.Strife and A.K.Chingra,1985,639．
(11) D.Z.Wang,J.Liu,C.K.Yao,W.C.Yu and Z.G.Wang:in Proc.2 nd Int.SAMPE Symposium,1991,Chiba,Japan.
(12) M.Taya and R.J.Arsenault:Metal Matrix Composites-Thermomechanical Behaviour.Pergamon Press,1989,51．
(13) Y.Flom and R.J.Arsenault:Mater.Sci.Eng.,1986,77,191．
(14) R.M.Fisher and RJ.Arsenault:Scripta Metall.,1983,17,67．
(15) M.Vogelsang,R.M.Fisher and R.J.Arsenault:Metall.Trans.,1986,17A,379．
(16) W.C.Yu,J.C.Yaun,J.Wang and Z.G.Wang:in Proc.4th Int.Conf.on Fatigue and Fatigue Threshold,Vol.Ⅱ,899,(Kitagawa and Tanaka eds.),1990,Honolulu,USA.
(17) N.Tsangarakis,J.M.Slepetz and J.Nunes:Recent Advances in Composites in the United States and Japan,ASTM STP864,ed.by J.R.Vinson and M.Taya,1975,95．
(18) J.Nunes,E.S.C.Chin,J.M.Slepetz and N.Tsangarakis:in Proc.ICCM-5,edited W.C.Harrigan,Jr.et al.,TMS of AIME,1989,723．
(19) C.C.Chamis and T.L.Sullivan:Fatigue of Composite Materials,ASTM STP 569,1975,95．
(20) W.W.Stinchcomb,K.L.Reifsnider,L.A.Marcus and R.S.Williams:ibid,1975,115．
(21) G.J.Dvorak and W.S.Johnson:Int.J.Fract.,1980,16,582．
(22) M.Gouda,K.M.Prewo and A.J.McEvily:Fatigue of Fibrous Composite Materials.ASTM STP 732,1981,101．
(23) S.S.Yau and G.Mayer:Mater.Sci.Eng.,1986,82,45．
(24) W.C.Yu,J.C.Yuan,Z.G.Wang and Q.W.Sui:Chin.J.Met.Sci.Technol.,1989,5,279．
(25) D.Z.Wang,J.Liu,C.K.Yao,W.C.Yu and Z.G.Wang:in Proc.2nd Int.SAMPE Symposium,Chiba,Japan,1991,773．
(26) CAO Li.JIANG Chiping,YAO Zhongkai and LEI Tingquan(T.C.Lei):Acta Metall.Sin.,1989,25,B179． (in Chinese)
(27) Z.M.Zhu,J.C.Yuan,W.C.Yu and Z.G.Wang:in Proc.of APCS-91,Vol.Ⅱ, Beijing,China,1991,898．
(28) J.K.Shang,W.Yu and R.O.Ritchie:Mater.Sci.Eng.,1988,A102,181．
(29) W.A.Logsdon and P.K.Liaw:Eng.Fract.Mech.,1986,24,737．
(30) S.Kumai,J.E.King and J.F.Knott:Fatigue Fract.Eng.Mater.Struct.,1990,13,511．
(31) J.K.Shang and R.O.Ritchie:Acta Metall.,1989,37,2267．
(32) K.Tanaka,M.Kinefuchi and Y.Akiniwa:Fatigue 90,Vol.Ⅱ,857．
(33) C.Atkinson:Int.J.Eng.Sci.,1972,10,45．
(34) A.A.Rubinstein: J.Appl.Mech.,1986,53,505．
(35) Z.G.Wang,D.L.Chen,X.X.Jiang and C.H.Shih:Phil.Mag.Lett.,1989,59,309．
(36) J.K.Shang and R.O.Ritchie:Metall.Trans.,1989,20A,897．
(37) G.C.Sih:Handbook of Stress Intensity Factors,Lehigh University Press,Bethleham,PA,1972．
(38) A.G.Evans,M.Y.He and J.W.Hutchinson:Acta Metall.Mater.,1989． 37,3249．
(39) Z.M.Sun,J.B.Li and Z.G.Wang:Acta Metall.Mater.,1992． to be published.
(40) S.X.Li.g.Z.Sun.Z.M.Sun and Z.G.Wang:Scripta Metall.Meter.,1991,25,2431．

[1]	Przemysł Kot; aw, BaczmańAndrzej ski, GadalińElż ska; bieta, WrońSebastian ski, WrońMarcin ski, WróMirosł bel; aw, Gizo Bokuchava, ScheffzüChristian k, Krzysztof Wierzbanowski. Evolution of phase stresses in Al/SiC_p composite during thermal cycling and compression test studied using diffraction and self-consistent models [J]. J. Mater. Sci. Technol., 2020, 36(0): 176-189.
[2]	Pablo D. Enrique, Ehsan Marzbanrad, Yahya Mahmoodkhani, Ali Keshavarzkermani, Hashem Al Momani, Ehsan Toyserkani, Norman Y. Zhou. Design of binder jet additive manufactured co-continuous ceramic-reinforced metal matrix composites [J]. J. Mater. Sci. Technol., 2020, 49(0): 81-90.
[3]	Kaustubh Bawane, Kathy Lu. Microstructure evolution of nanostructured ferritic alloy with and without Cr₃C₂ coated SiC at high temperatures [J]. J. Mater. Sci. Technol., 2020, 43(0): 126-134.
[4]	P.A. Morton, H.C. Taylor, L.E. Murr, O.G. Delgado, C.A. Terrazas, R.B. Wicker. In situ selective laser gas nitriding for composite TiN/Ti-6Al-4V fabrication via laser powder bed fusion [J]. J. Mater. Sci. Technol., 2020, 45(0): 98-107.
[5]	Shuo Yin, Wenya Li, Bo Song, Xingchen Yan, Min Kuang, Yaxin Xu, Kui Wen, Rocco Lupoi. Deposition of FeCoNiCrMn high entropy alloy (HEA) coating via cold spraying [J]. J. Mater. Sci. Technol., 2019, 35(6): 1003-1007.
[6]	Liuliu Han, Kun Li, Cheng Qian, Jingwen Qiu, Chengshang Zhou, Yong Liu. Wear behavior of light-weight and high strength Fe-Mn-Ni-Al matrix self-lubricating steels [J]. J. Mater. Sci. Technol., 2019, 35(4): 623-630.
[7]	Sree Manu K.M., Ajay Raag L., Rajan T.P.D., Pai B.C., Petley Vijay, Namdeo Verma Shweta. Self-lubricating bidirectional carbon fiber reinforced smart aluminum composites by squeeze infiltration process [J]. J. Mater. Sci. Technol., 2019, 35(11): 2559-2569.
[8]	Junho Lee, Dongju Lee, Myung Hoon Song, Wonhyuk Rhee, Ho Jin Ryu, Soon Hyung Hong. In-situ synthesis of TiC/Fe alloy composites with high strength and hardness by reactive sintering [J]. J. Mater. Sci. Technol., 2018, 34(8): 1397-1404.
[9]	Yu-Shi Yi, Yi Meng, Dan-Qing Li, Sumio Sugiyama, Jun Yanagimoto. Partial melting behavior and thixoforming properties of extruded magnesium alloy AZ91 with and without addition of SiC particles with a volume fraction of 15% [J]. J. Mater. Sci. Technol., 2018, 34(7): 1149-1161.
[10]	J.F. Zhang, X.X. Zhang, Q.Z. Wang, B.L. Xiao, Z.Y. Ma. Simulations of deformation and damage processes of SiCp/Al composites during tension [J]. J. Mater. Sci. Technol., 2018, 34(4): 627-634.
[11]	Jinlong Du, Yuan Huang, Chan Xiao, Yongchang Liu. Building metallurgical bonding interfaces in an immiscible Mo/Cu system by irradiation damage alloying (IDA) [J]. J. Mater. Sci. Technol., 2018, 34(4): 689-694.
[12]	Kang Yang, Wenya Li, Chunjie Huang, Xiawei Yang, Yaxin Xu. Optimization of cold-sprayed AA2024/Al₂O₃ metal matrix composites via friction stir processing: Effect of rotation speeds [J]. J. Mater. Sci. Technol., 2018, 34(11): 2167-2177.
[13]	Zhao Ke, Liu Zhenyu, Xiao Bolyu, Ma Zongyi. Friction stir welding of carbon nanotubes reinforced Al-Cu-Mg alloy composite plates [J]. J. Mater. Sci. Technol., 2017, 33(9): 1004-1008.
[14]	D.R. Ni, J.J. Wang, Z.Y. Ma. Shape Memory Effect, Thermal Expansion and Damping Property of Friction Stir Processed NiTip/Al Composite [J]. J. Mater. Sci. Technol., 2016, 32(2): 162-166.
[15]	Wang Zhiguo,Li Chuanpeng,Wang Huiyuan,Zhu Xian,Wu Min,Li Jiehua,Jiang Qichuan. Aging Behavior of Nano-SiC/2014Al Composite Fabricated by Powder Metallurgy and Hot Extrusion Techniques [J]. J. Mater. Sci. Technol., 2016, 32(10): 1008-1012.