High temperature calcium-magnesium-alumina-silicate (CMAS) corrosion behavior of directionally solidified Al2O3/YAG eutectic ceramic

doi:10.1016/j.jmst.2023.04.060

Abstract

Abstract: The corrosion resistance to CaO-MgO-Al₂O₃-SiO₂ (CMAS) is critically important for the high temperature structural parts applied in aero-engine. We herein studied the high-temperature CMAS corrosion behavior at 1300 °C of directionally solidified Al₂O₃/YAG (Y₃Al₅O₁₂) eutectic ceramic. The systematic correlations between the CMAS corrosion resistance and unique solidification microstructure were established. The rapid reaction between CMAS melt and Al₂O₃/YAG eutectic and CMAS attacking depth could be successfully decreased. This happened because of their low chemical activity, the dense structure of the eutectic substrate and the accelerated crystallization of anorthite (CaAl₂Si₂O₈) along the CMAS-eutectic interface. Additionally, the reaction layer thickness reached lower than 40.58 μm after the corrosion for 32 h, presenting excellent CMAS corrosion resistance for the solidified eutectic ceramic. The dissolution-reprecipitation mechanism of CMAS corrosion was clearly revealed by TEM and EDS analysis in the CMAS-YAG interaction region. The interfacial structure had a low misfit of -1.81% and well-matched crystallographic relationship based on the near-coincident site lattice (NCSL) model. The superior CMAS corrosion resistance and high flexural strength stability (up to 1873 K) of the directionally solidified Al₂O₃/YAG eutectic ceramic highlight it as a promising high-temperature structural candidate material in aerospace and aeronautics industries.

Key words: Al₂O₃/YAG eutectic ceramic, Optical Basicity, CMAS corrosion behavior, Mechanical properties

Haijun Su, Zhonglin Shena, Di Zhao, Yinuo Guo, Xiang Li, Hao Jiang, Dong Dong, Chubin Yang. High temperature calcium-magnesium-alumina-silicate (CMAS) corrosion behavior of directionally solidified Al₂O₃/YAG eutectic ceramic[J]. J. Mater. Sci. Technol., 2023, 165: 66-74.

References

[1] R. Naraparaju, H. Lau, M. Lange, C. Fischer, D. Kramer, U. Schulz, K. Weber, Surf. Coat. Technol. 337(2018) 198-208.
[2] L. Wei, L. Guo, M. Li, H. Guo, J. Eur. Ceram. Soc. 37 (2017) 4991-50 0 0.
[3] J. Wang, M. Chen, C. Li, L. Chen, Y. Yu, Y. Wang, B. Liu, Q. Jing, Surf. Coat. Technol. 428(2021) 127879.
[4] S. Morelli, V. Testa, G. Bolelli, O. Ligabue, E. Molinari, N. Antolotti, L. Lusvarghi, J. Eur. Ceram.Soc. 40(2020) 4084-4100.
[5] T. Wang, F. Shao, J. Ni, H. Zhao, Y. Zhuang, J. Sheng, X. Zhong, J. Yang, S. Tao, Ceram. Int. 46(2020) 18698-18706.
[6] R. Kumar, E. Jordan, M. Gell, J. Roth, C. Jiang, J. Wang, S. Rommel, Surf. Coat. Technol. 327(2017) 126-138.
[7] T.Z. Tu, J.X. Liu, L. Zhou, Y.C. Liang, G.J. Zhang, J. Eur. Ceram.Soc. 42(2022) 649-657.
[8] B. Zhang, Y. Yu, L. Guo, S. Kang, Y. Cheng, Z. Yan, L. Wang, Ceram. Int. 48(2022) 32877-32885.
[9] L. Guo, G. Li, J. Wu, X. Wang, J. Adv. Ceram. 11(2022) 945-960.
[10] G. Li, C. Cai, Y. Wang, Y. Zhou, L. Yang, J. Lu, G. Zhou, Corros. Sci. 149(2019) 249-256.
[11] Z.Y. Tan, Z.H. Yang, W. Zhu, L. Yang, Y.C. Zhou, X.P. Hu, Ceram. Int. 46(2020) 25242-25248.
[12] D. Li, P. Jiang, R. Gao, F. Sun, X. Jin, X. Fan, J. Adv. Ceram. 10(2021) 551-564.
[13] Z. Fan, Y. Zhao, Q. Tan, N. Mo, M.-X. Zhang, M.Lu, H. Huang, Acta Mater. 170(2019) 24-37.
[14] X. Wang, N. Zhang, Y. Zhong, B. Jiang, L. Lou, J. Zhang, J. Wang, J. Mater. Sci.Technol. 35(2019) 1982-1988.
[15] J.Y. Pastor, J. Llorca, A. Salazar, P.B. Oliete, I. De Francisco, J.I. Peña, J. Am. Ceram.Soc. 88(2005) 1488-1495.
[16] Y. Waku, N. Nakagawa, T. Wakamoto, H. Ohtsubo, K. Shimizu, Y. Kohtoku, J. Mater. Sci. 33(1998) 1217-1225.
[17] J. Han, Y. Zou, D. Wu, J. Chen, Y. Zhang, Surf. Coat. Technol. 446(2022) 128799.
[18] X.-F. Zhang, K.-S. Zhou, W. Xu, B.-Y. Chen, J.-B. Song, M. Liu, Surf. Coat. Technol. 261(2015) 54-59.
[19] R. Kumar, S. Rommel, C. Jiang, E.H. Jordan, Surf. Coat. Technol. 432(2022) 128039.
[20] Y. Liu, H. Su, Z. Lu, Z. Shen, Y. Guo, D. Zhao, S. Li, J. Zhang, L. Liu, H. Fu, Ceram. Int. 48(2022) 23598-23608.
[21] P.B. Oliete, J.I. Peña, A. Larrea, V.M. Orera, J. Llorca, J.Y. Pastor, A. Martín, J. Segurado, Adv. Mater. 19(2007) 2313-2318.
[22] N. Nakagawa, H. Ohtsubo, A. Mitani, K. Shimizu, Y. Waku, J. Eur. Ceram.Soc. 25(2005) 1251-1257.
[23] Z. Fan, Y. Zhao, Q. Tan, B. Yu, M.-X. Zhang, H.Huang, Scr. Mater. 178(2020) 274-280.
[24] Y. Liu, H. Su, Z. Shen, D. Zhao, Y. Guo, S. Li, M. Guo, L. Liu, H. Fu, J. Mater. Sci.Technol. 146(2023) 86-101.
[25] F. Stolzenburg, M.T. Johnson, K.N. Lee, N.S. Jacobson, K.T. Faber, Surf. Coat. Technol. 284(2015) 44-50.
[26] E.M. Zaleski, University of California, 2013.
[27] H. Chang, C. Cai, Y. Wang, Y. Zhou, L. Yang, G. Zhou, Surf. Coat. Technol. 324(2017) 577-584.
[28] F.R.N. Amsterdam, 1979.
[29] X. Wang, J. Wang, L. Sun, H. Zhang, L. Wang, L. Lou, J. Zhang, Scr. Mater. 108(2015) 31-34.
[30] D. Lorenz, A. Zeckzer, U. Hilpert, P. Grau, H. Johansen, H.S. Leipner, Phys. Rev. B 67 (2003) 172101.
[31] X. Wang, Z. Tian, W. Zhang, Y. Zhong, Q. Xian, J. Zhang, J. Wang, J. Eur. Ceram.Soc. 38(2018) 3610-3617.

High temperature calcium-magnesium-alumina-silicate (CMAS) corrosion behavior of directionally solidified Al₂O₃/YAG eutectic ceramic

PDF (PC)

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Recommended Articles

Metrics

Comments

[1]	Xirui Lv, Yiming Lei, Zhao Zhang, Jie Zhang, Jingyang Wang. lerating the design of multicomponent rare earth silicates for SiC_f/SiC CMC by combinatorial material chip design and high throughput screening [J]. J. Mater. Sci. Technol., 2023, 150(0): 96-103.
[2]	Xianghui Zhu, Xusheng Yang, Weijiu Huang, Weiyi Qiu, Xin Wang, Fei Guo, Li Hu, Miao Gong. Influence of pre-stretching on the tensile strength, fatigue properties and the in-plane anisotropy in Al-Cu-Li alloy AA2099 [J]. J. Mater. Sci. Technol., 2023, 145(0): 249-259.
[3]	Yixiao Yang, Enwei Sun, Zhimin Xu, Huashan Zheng, Bin Yang, Rui Zhang, Wenwu Cao. Sm and Mn co-doped PMN-PT piezoelectric ceramics: Defect engineering strategy to achieve large d₃₃ and high Q_m [J]. J. Mater. Sci. Technol., 2023, 137(0): 143-151.
[4]	Guangqi He, Yi Zhang, Pei Yao, Xingchao Li, Ke Ma, Jun Zuo, Meishuan Li, Changsheng Liu, Jingjun Xu. A novel medium-entropy (TiVNb)₂AlC MAX phase: Fabrication, microstructure, and properties [J]. J. Mater. Sci. Technol., 2023, 137(0): 91-99.
[5]	Yu Pan, Jinshan Zhang, Jianzhuo Sun, Yanjun Liu, Ce Zhang, Rui Li, Fan Kuang, Xinxin Wu, Xin Lu. Enhanced strength and ductility in a powder metallurgy Ti material by the oxygen scavenger of CaB₆ [J]. J. Mater. Sci. Technol., 2023, 137(0): 132-142.
[6]	Huan Liu, Hai Wang, Ling Ren, Dong Qiu, Ke Yang. Antibacterial copper-bearing titanium alloy prepared by laser powder bed fusion for superior mechanical performance [J]. J. Mater. Sci. Technol., 2023, 132(0): 100-109.
[7]	Hao Zhang, Ziyi Ren, Yonggang Tong, Yongle Hu, Xixi Ji, Lingwei Yang, Kaiming Wang, Jingzhong Fang, Hui Chen, Xiubing Liang. Introduction of nanotwins into nanoprecipitations strengthened CoCrNiMo_0.2 alloy to achieve strength and ductility trade-off: A comparative research [J]. J. Mater. Sci. Technol., 2023, 156(0): 172-182.
[8]	Haozhe Li, Xiaolin Li, Chi Jin, Qian Li, Qiang Ma, Ke Hua, Haifeng Wang, Weimin Liu. Mechanical and tribological performance of AlCr_0.5NbTa_xTi_4-_x (x = 0, 0.5, 1) refractory high-entropy alloys [J]. J. Mater. Sci. Technol., 2023, 156(0): 241-253.
[9]	Haixiao Zhao, Lu Sun, Guoqun Zhao, Junquan Yu, Fei Liu, Ximan Sun, Zhengfeng Lv, Shanpeng Cao. Abnormal grain growth behavior and mechanism of 6005A aluminum alloy extrusion profile [J]. J. Mater. Sci. Technol., 2023, 157(0): 42-59.
[10]	Xin Zhang, Xin Li, Lei Liu, Bo Li, Xiaodong Hou, Deng Pan, Lina Gao, Shufeng Li. Interface regulation strategy of Al-CNTs composite induced by Al-Si eutectic reaction and its strengthening mechanism [J]. J. Mater. Sci. Technol., 2023, 151(0): 1-9.
[11]	D.L. Gong, H.L. Wang, S.H. Hao, P. Liu, X. Yang, Y.N. Jiang, W.J. Wang, K. Lin, B. Li, K. Du, Y.D. Wang, R. Yang, Y.L. Hao. Ordering-induced Elinvar effect over a wide temperature range in a spinodal decomposition titanium alloy [J]. J. Mater. Sci. Technol., 2023, 150(0): 245-255.
[12]	Jianwei Tang, Liang Chen, Zhigang Li, Biaohua Que, Guoqun Zhao, Cunsheng Zhang. Suppressing abnormal grain growth and switching precipitation behaviors in ZK60 Mg profile by inducing pre-tension [J]. J. Mater. Sci. Technol., 2023, 155(0): 89-101.
[13]	Jinxing Sun, Daorong Ye, Ji Zou, Xiaoteng Chen, Yue Wang, Jinsi Yuan, Haowen Liang, Hongqiao Qu, Jon Binner, Jiaming Bai. A review on additive manufacturing of ceramic matrix composites [J]. J. Mater. Sci. Technol., 2023, 138(0): 1-16.
[14]	Zhang-Zhi Shi, Xiang-Min Li, Sheng-Lian Yao, Yun-Zhi Tang, Xiao-Jing Ji, Qiang Wang, Xi-Xian Gao, Lu-Ning Wang. 300 MPa grade biodegradable high-strength ductile low-alloy (BHSDLA) Zn-Mn-Mg alloys: An in vitro study [J]. J. Mater. Sci. Technol., 2023, 138(0): 233-244.
[15]	Guodong Niu, Jianfeng Wang, Jinwen Ye, Jian Mao. Enhancing Fe content tolerance in A356 alloys for achieving low carbon footprint aluminum structure castings [J]. J. Mater. Sci. Technol., 2023, 161(0): 180-191.