Effect of Y and Ce on the microstructure, mechanical properties and anisotropy of as-rolled Mg-8Li-1Al alloy

doi:10.1016/j.jmst.2019.04.045

材料科学与技术 ›› 2020, Vol. 39 ›› Issue (0): 124-134.DOI: 10.1016/j.jmst.2019.04.045

收稿日期:2019-03-05 修回日期:2019-04-08 接受日期:2019-04-17 出版日期:2020-02-15 发布日期:2020-03-11

Effect of Y and Ce on the microstructure, mechanical properties and anisotropy of as-rolled Mg-8Li-1Al alloy

Feng Zhong^a, Huajie Wu^a, Yunlei Jiao^c, Ruizhi Wu^a^b^*(), Jinghuai Zhang^a, Legan Hou^a, Milin Zhang^a

^a Key Laboratory of Superlight Material and Surface Technology (Harbin Engineering University), Ministry of Education, Harbin 150001, China
^b College of Science, Heihe University, Heihe University, Heihe 164300, China
^c Tianjin Institute of Aerospace Mechanical and Electrical Equipment, Tianjin 300301, China

Received:2019-03-05 Revised:2019-04-08 Accepted:2019-04-17 Online:2020-02-15 Published:2020-03-11
Contact: Wu Ruizhi

摘要/Abstract

Abstract:

The effects of combined addition of Y and Ce on the microstructure, mechanical properties and anisotropy of as-rolled Mg-8Li-1Al (LA81) alloy were studied. The combined addition of Y and Ce improves the mechanical properties with a low plasticity loss by solution strengthening, dispersion strengthening, grain refinement strengthening. Mg-8Li-1Al-0.6Y-0.6Ce (LA81-0.6Y-0.6Ce) has better mechanical properties and shows an almost isotropy. It possesses an ultimate tensile strength of 278.7 MPa and an elongation of 15.0%. Compared to LA81 alloy, the ultimate tensile strength increases by about 17.6% with an elongation reduction of only 3.5%, and a good isotropy of ultimate tensile strength and elongation (the value of r_avg is near 1).

Key words: Mg-Li alloy, Cross rolling, Alloying, Mechanical properties, Anisotropy

. [J]. 材料科学与技术, 2020, 39(0): 124-134.

Feng Zhong, Huajie Wu, Yunlei Jiao, Ruizhi Wu, Jinghuai Zhang, Legan Hou, Milin Zhang. Effect of Y and Ce on the microstructure, mechanical properties and anisotropy of as-rolled Mg-8Li-1Al alloy[J]. J. Mater. Sci. Technol., 2020, 39(0): 124-134.

图/表 13

Fig. 1. Schematic diagram of the tensile testing specimens.

Fig. 2. Tensile stress?strain curves of as-rolled LA81-xY-yCe sheets: (a) LA81, (b) LA81-0.6Y, (c) LA81-0.6Ce, (d) LA81-0.6Ce-0.3Y, (e) LA81-0.6Ce-0.6Y, (f) LA81-0.6Ce-0.9Y, (g) LA81-0.6Ce-1.2Y.

Fig. 3. Mechanical behavior of as-rolled LA81-xY-yCe sheets at room temperatures: (a) ultimate tensile strength, (b) yield strength, (c) elongation.

Table 1 Anisotropic factor of as-rolled sheets.

Alloys	r value			r_avg	△r
	RD	45°	TD
LA81	2.40	2.62	1.16	2.2	0.84
LA81-0.6Y	1.30	2.14	1.74	1.83	0.62
LA81-0.6Ce	1.51	1.30	0.53	1.16	0.28
LA81-0.6Ce-0.3Y	0.95	1.60	1.21	1.34	0.56
LA81-0.6Ce-0.6Y	0.72	1.06	1.46	1.07	0.03
LA81-0.6Ce-0.9Y	0.93	1.07	1.40	1.11	0.095
LA81-0.6Ce-1.2Y	2.03	1.12	1.44	1.42	0.615

Fig. 4. Fracture morphologies of as-rolled LA81-xY-yCe alloys at room temperature: (a) LA81, (b) LA81-0.6Y, (c) LA81-0.6Ce, (d) LA81-0.6Ce-0.3Y, (e) LA81-0.6Ce-0.6Y, (f) LA81-0.6Ce-0.9Y, (g) LA81-0.6Ce-1.2Y.

Fig. 5. XRD patterns of as-cast LA81-xY-yCe.

Table 2 Lattice parameters and c/a ratio of as-cast LA81-xY-yCe.

Alloys	a (Å)	c (Å)	c/a
LA81	3.19505	5.13255	1.6064
LA81-0.6Y	3.19355	5.12999	1.6063
LA81-0.6Ce	3.19434	5.12907	1.6056
LA81-0.6Ce-0.3Y	3.19454	5.12983	1.6058
LA81-0.6Ce-0.6Y	3.19393	5.12858	1.6057
LA81-0.6Ce-0.9Y	3.19198	5.12608	1.6059
LA81-0.6Ce-1.2Y	3.19306	5.12798	1.6059

Fig. 6. XRD patterns of as-rolled LA81-xY-yCe.

Fig. 7. SEM images of as-cast LA81-xY-yCe: (a) LA81, (b) LA81-0.6Y, (c) LA81-0.6Ce, (d) LA81-0.6Ce-0.3Y, (e) LA81-0.6Ce-0.6Y, (f) LA81-0.6Ce-0.9Y, (g) LA81-0.6Ce-1.2Y.

Fig. 8. SEM images of as-rolled LA81-xY-yCe: (a) LA81, (b) LA81-0.6Y, (c) LA81-0.6Ce, (d) LA81-0.6Ce-0.3Y, (e) LA81-0.6Ce-0.6Y, (f) LA81-0.6Ce-0.9Y, (g) LA81-0.6Ce-1.2Y.

Fig. 9. Optical micrographs of as-rolled LA81-xY-yCe: (a) LA81, (b) LA81-0.6Y, (c) LA81-0.6Ce, (d) LA81-0.6Ce-0.6Y.

Fig. 10. 3D optical micrographs of as-rolled LA81-xY-yCe: (a) LA81, (b) LA81-0.6Y, (c) LA81-0.6Ce, (d) LA81-0.6Ce-0.6Y.

Fig. 11. Pole figures of as-rolled Mg-8Li-Al-xY-yCe alloy: (a) (0002) pole figure of LA81, (b) (0002) pole figure of LA81-0.6Y-0.6Ce, (c) (110) pole figure of LA81, (d) (110) pole figure of LA81 LA81-0.6Y-0.6Ce.

参考文献

[1]	X.J. Wang, D.K. Xu, R.Z. Wu, X.B. Chen, Q.M. Peng, L. Jin, Y.C. Xin, Z.Q. Zhang, Y. Liu, X.H. Chen, G. Chen, K.K. Deng, H.Y. Wang, J. Mater. Sci. Technol. 34 (2018) 245-247.
[2]	B.Y. Qian, W. Miao, M. Qiu, F. Gao, D.H. Hu, J.F. Sun, R.Z. Wu, B. Krit, S. Betsofen, Acta. Metall. Sin. (Engl. Lett.) 32 (2019) 194-204.
[3]	D.K. Guan, W.M. Rainforth, L. Ma, B. Wynne, J.H. Gao, Acta Mater. 126 (2017) 132-144.
[4]	R.Z. Wu, Y.D. Yan, G.X. Wang, L.E. Murr, W. Han, Z.W. Zhang, M.L. Zhang, Int. Mater. Rev. 60 (2015) 65-100.
[5]	S.Y. Betsofen, L.L. Rokhlin, R.Z. Wu, A.A. Lozovan, I.I. Voskresenskaya, Russ. Metall. 11 (2014) 920-927.
[6]	L.Z. Liu, X.H. Chen, F.S. Pan, S.Y. Gao, C.Y. Zhao, J. Alloys Compd. 688 (2016) 537-541.
[7]	T.Z. Wang, T.L. Zhu, R.Z. Wu, W. Miao, J.H. Zhang, M.L. Zhang, Mater. Des. 85 (2015) 190-196.
[8]	L.Q. Wu, T.L. Zhang, C.G. Cui, R.Z. Wu, M.L. Zhang, L.G. Hou, Phys. Met. Metallogr. 117 (2016) 735-741.
[9]	J. Zhao, J. Zhang, W.C. Liu, G.H. Wu, L. Zhang, Mater. Sci. Eng. A 650 (2016) 240-247.
[10]	L.L. Chang, C.C. Shi, H.W. Cui, Trans. Nonferrous Met. Soc. 28 (2018) 30-35.
[11]	R.H. Li, F.S. Pan, B. Jiang, Q.S. Yang, A.T. Tang, Mater. Des. 46 (2013) 922-927.
[12]	Y.H. Sun, R.C. Wang, C.Q. Peng, Y. Feng, Mater. Sci. Eng. A 733 (2018) 429-439.
[13]	G.H. Park, J.T. Kim, H.J. Park, Y.S. Kim, H.J. Jeong, N. Lee, Y. Seo, J.Y. Suh, H.T. Son, W.M. Wang, J.M. Park, K.B. Kim, J. Alloys Compd. 680 (2016) 116-120.
[14]	J.T. Kim, G.H. Park, Y.S. Kim, S.H. Hong, H.J. Park, J.Y. Suh, H.T. Son, M.H. Lee, J.M. Park, K.B. Kim, J. Alloys Compd. 687 (2016) 821-826.
[15]	Y.N. Lin, H.Y. Wu, G.Z. Zhou, C.H. Chiu, S. Lee, Mater. Des. 29 (2008) 2061-2065.
[16]	Y. Zeng, B. Jiang, Q.R. Yang, G.F. Quan, J.J. He, Z.T. Jiang, F.S. Pan, Mater. Sci. Eng. A 700 (2017) 59-65.
[17]	R. Narayanasamy, C.S. Narayanan, Mater. Sci. Eng. A 399 (2005) 292-307.
[18]	T. Bhattacharjee, C.L. Mendis, T.T. Sasaki, T. Ohkubo, K. Hono, Scr. Mater. 67 (2012) 967-970.
[19]	T.L. Zhang, T. Tokunaga, M. Ohno, M.L. Zhang, K. Matsuura, Acta Metall. Sin. (Engl. Lett.). 32 (2019) 169-177.
[20]	J.T. Kim, H.J. Jeong, Y. Moon, K.B. Kim, H.T. Son, C. Jeon, J.W. Sim, S. Moon, J.M. Park, J. Alloys Compd. 711 (2017) 243-249.
[21]	J.H. Zhang, J.L. Shu, R.Z. Wu, L.G. Hou, M.L. Zhang, J. Magnes. Alloys 6 (2018) 277-291.
[22]	B.L. Wu, G. Wan, X.H. Du, Y.D. Zhang, F. Wagner, C. Esling, Mater. Sci. Eng. A 573 (2013) 205-214.
[23]	G.Q. Li, J.H. Zhang, R.Z. Wu, Y. Feng, S.J. Liu, X.J. Wang, Y.F. Jiao, Q. Yang, J. Meng, J. Mater. Sci. Technol. 34 (2018) 1076-1084.
[24]	Z. Yu, Y. Huang, W. Gan, C.L. Mendis, Z. Zhong, H.G. Brokmeier, N. Hort, J. Meng, Mater. Sci. Eng. A 657 (2016) 259-268.
[25]	H. Liu, F. Xue, J. Bai, A.B. Ma, J.H. Jiang, J. Mater. Sci. Technol. 32 (2016) 1267-1273.
[26]	S.R. Agnew, M.H. Yoo, C.N. Tome, Acta Mater. 49 (2011) 4277-4289.
[27]	C.F. Fang, G.X. Liu, X.T. Liu, H. Hao, X.G. Zhang, Mater. Sci. Eng. A 701 (2017) 314-318.
[28]	L. Dezerald, D. Rodney, E. Clouet, Nat. Commun. 7 (2016) 11695.
[29]	F. Zhong, T.Z. Wang, R.Z. Wu, L.G. Hou, J.H. Zhang, M.L. Zhang, A.P. Dong, Adv. Eng. Mater. 19 (2017), 1600817.
[30]	H. Chang, M.Y. Zheng, K. Wu, Mater. Sci. Eng. A 527 (2010) 7176-7183.
[31]	C.L. Cui, T.L. Zhang, J.F. Sun, R.Z. Wu, M.L. Zhang, Rare Met. Mater. Eng. 43 (5) (2014) 1177-1180 (in Chinese).

Effect of Y and Ce on the microstructure, mechanical properties and anisotropy of as-rolled Mg-8Li-1Al alloy

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

图/表 13

参考文献

相关文章 0

编辑推荐

Metrics

本文评价