Proportional Limit Stress and Residual Thermal Stress of 3D SiC/SiC Composite

doi:10.1016/j.jmst.2014.08.004

Abstract

Abstract: Proportional limit stress (PLS) and residual thermal stresses (RTS) of 3D SiC/SiC composite were investigated. PLS was obtained by four different methods from the monotonic stress-strain response curve to get a convincing value. RTS in the SiC matrix was quantified by solving the geometric intersection point of the regression lines of hysteresis loops from the periodical loading-unloading-reloading cycle test curve. Classical ACK model and analytical formulas were used to analytically calculate the PLS and RTS of 3D SiC/SiC composite. Good agreement between the experimental results and the analytical calculation was observed. And relationship between the PLS and the RTS of 3D SiC/SiC was discussed.

Key words: Proportional limit stress, Residual thermal stresses, Mechanical properties, Ceramic matrix composites

Shanhua Liu, Litong Zhang, Xiaowei Yin, Yongsheng Liu, Laifei Cheng. Proportional Limit Stress and Residual Thermal Stress of 3D SiC/SiC Composite[J]. J. Mater. Sci. Technol., 2014, 30(10): 959-964.

References

[1] T.M. Besmann, R.A. Lowden, in: R. Naslain (Ed.), Overview of Chemical Vapor Infiltration, High Temperature Ceramic Matrix Composites, Woodhead Publications, Bordeaux, 1993, p. 215.
[2] S. Jacques, A. Guette, F. Langlais, R. Naslain, S. GouJard, J. Eur.Ceram. Soc. 17 (1997) 1083-1092.
[3] L.L. Snead, R.H. Jones, A. Kohyama, P. Fenici, J. Nucl. Mater.233e237 (1996) 26-36.
[4] R.H. Jones, D. Steiner, H.L. Heinisch, G.A. Newsome, H.M. Herch,J. Nucl. Mater. 245 (1997) 87-127.
[5] K. Hironaka, T. Nozawa, T. Hinoki, N. Igawa, J. Nucl. Mater. 307e 311 (2002) 1093-1097.
[6] K. Shimoda, A. Kohyama, T. Hinoki, Compos. Sci. Technol. 69(2009) 1623-1628.
[7] T. Hinoki, J. Plasma Fusion Res. 80 (2004) 31-35.
[8] Ceramic Matrix Composites, MIL-HDBK-17, (Yellow Pages), vol.5, Department of Defense Handbook, Secretariat: Materials Science Corp, Fort Washington, Penn., 2000.
[9] R. Naslain, J. Lamon, R. Pailler, X. Bourrat, A. Guette, F. Langlais,Compos. Pt. A Appl. Sci. Manuf 30 (1999) 537-547.
[10] Y.D. Xu, L.F. Cheng, L.T. Zhang, Mater. Sci. Eng. A 318 (2001)183-188.
[11] X.G. Luan, L.F. Cheng, C.W. Xie, Compos. Sci. Technol. 88 (2013)178-183.
[12] M. Takeda, J. Sakamoto, Y. Imai, H. Ichikawa, Compos. Sci.Technol. 59 (1999) 813-819.
[13] ASTM C-1275, Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-reinforced Advanced Ceramics with Solid Rectangular Cross-section Test Specimens at Ambient Temperature,ASTM, West Conshohocken, PA, 2000.
[14] S. Kalluri, A. Calomino, D.N. Brewer, Ceram. Eng. Sci. Proc. 25(2004) 79-86.
[15] M. Steen, J.L. Vall, Mater. Sci. Eng. A 250 (1998) 217-221.
[16] G.N. Morscher, in: D.O. Thompson, D.E. Chimenti (Eds.), Review of Progress in Quantitative Nondestructive Evaluation, Vol. 509,American Institute of Physics, 2000, pp. 383-390.
[17] G.N. Morscher, H.M. Yun, J.A. DiCarlo, J. Am. Ceram. Soc. 90(2007) 3185-3193.
[18] E. Vagaggini, J. Domergue, A.G. Evans, J. Am. Ceram. Soc. 78(1995) 2709-2720.
[19] G.N. Morscher, M. Singh, J.D. Kiser, M. Freedman, R. Bhatt,Compos. Sci. Technol. 67 (2007) 1009-1017.
[20] J. Aveston, G.A. Copper, A. Kelly, in: The Property of Fiber Composites Conference Proceedings of National Physical Laboratories,IPC Science and Technology Press, Teddington, UK, 1971,pp. 15-18.
[21] J.M. Domergue, E. Vagaggini, A.G. Evans, J. Am. Ceram. Soc. 78(1995) 2721-2731.
[22] J.W. Hutchinson, H.M. Jensen, Mech. Mater. 9 (1990) 139-163.
[23] H. Mei, Compos. Sci. Technol. 68 (2008) 3285-3292.
[24] N.P. Bansal, Ceram. Int. 28 (2002) 527-540.