Microstructure and abrasive wear resistance of an alloyed ductile iron subjected to deep cryogenic and austempering treatments

doi:10.1016/j.jmst.2017.08.003

材料科学与技术 ›› 2017, Vol. 33 ›› Issue (12): 1549-1554.DOI: 10.1016/j.jmst.2017.08.003

收稿日期:2016-12-17 修回日期:2017-02-06 接受日期:2017-02-19 出版日期:2017-12-20 发布日期:2018-01-30

Microstructure and abrasive wear resistance of an alloyed ductile iron subjected to deep cryogenic and austempering treatments

Cui Junjun^a^b, Chen Liqing^a^*()

^aState Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, China
^bCollege of Mechanical and Vehicle Engineering, Shenyang Institute of Technology, Fushun 113122, China

Received:2016-12-17 Revised:2017-02-06 Accepted:2017-02-19 Online:2017-12-20 Published:2018-01-30
Contact: Chen Liqing

摘要/Abstract

Abstract:

To further improve the mechanical performance of a new alloyed austempered ductile iron (ADI), deep cryogenic treatment (DCT) has been adopted to investigate the effect of DCT time on the microstructure and mechanical behaviors of the alloyed ADI Fe-3.55C-1.97Si-3.79Ni-0.71Cu-0.92Mo-0.64Cr-0.36Mn-0.30 V (in wt.%). With increasing the DCT time, more austenite transformed to martensite and very fine carbides precipitated in martensite in the extended period of DCT. The amount of austenite decreased in alloyed ductile irons, while that of martensite and carbide precipitation increased. The alloyed ADI after DCT for 6 h had the highest hardness and compressive strength, which can be attributed to the formation of more plate-like martensite and the finely precipitated carbides. There was a gradual decrease in hardness and compressive strength with increasing the DCT time to 12 h because of the dissolution of M₃C carbide. After tempering, there was a decrease in mechanical properties compared to the direct DCT sample, which was caused by the occurrence of Ostwald ripening of precipitated carbides. The optimum wear resistance was achieved for the alloyed ADI after DCT for 6 h. The wear mechanism of the alloyed ADI in associating with DCT is mainly consisted of micro-cutting wear and some plastic deformation wear.

Key words: Alloyed ductile iron, Austempering, Deep cryogenic treatment (DCT), Microstructure, Mechanical properties

. [J]. 材料科学与技术, 2017, 33(12): 1549-1554.

Cui Junjun, Chen Liqing. Microstructure and abrasive wear resistance of an alloyed ductile iron subjected to deep cryogenic and austempering treatments[J]. J. Mater. Sci. Technol., 2017, 33(12): 1549-1554.

图/表 10

Table 1 Processes of the austempered alloyed ductile iron with cryogenic deep treatment.

Samples	Treatment processes
DCT-00	Austempering + untreated
DCT-04	Austempering + deep cryogenic treatment at -196 °C for 4 h
DCT-06	Austempering + deep cryogenic treatment at -196 °C for 6 h
DCT-12	Austempering + deep cryogenic treatment at -196 °C for 12 h
DCT-04T	Austempering + deep cryogenic treatment at -196 °C for 4 h +tempering at 450 °C for 2 h

Fig. 1. Optical microstructure of the alloyed ductile iron at isothermally quenched state (DCT-00).

Fig. 2. XRD pattern of the austempered alloyed bainitic ductile iron.

Fig. 3. Optical microstructures of the austempered alloyed ductile iron after deep cryogenic treatment: (a) DCT-04, (b) DCT-06, (c) DCT-12, (d) DCT-04T.

Fig. 4. XRD profiles of austempered alloyed ductile iron with deep cryogenic treatment at different holding time.

Fig. 5. XRD pattern of the austempered alloyed ductile iron with DCT-04T treatment.

Fig. 6. TEM images of martensite (a) and carbide precipitation (b) of austempered alloyed ductile iron after DCT-04T treatment.

Table 2 Hardness and compressive strength of the alloyed ADI after various processes of DCT.

Samples	Hardness (HRC)	Compressive strength (MPa)
DCT-00	62.9	3000
DCT-04	64.4	2870
DCT-06	66.0	3140
DCT-12	65.8	3040
DCT-04T	63.9	2770

Table 3 Wear resistance of the alloyed ADI after various processes of DCT.

Samples	Weight loss (g)	Wear resistance (g^-1)
DCT-04	0.7322	1.3657
DCT-06	0.5936	1.6846
DCT-12	0.6172	1.6202
DCT-04T	0.7939	1.2596

Fig. 7. Worn surface morphologies of the alloyed ADI after various processes of DCT. (a) DCT-04, (b) DCT-06, (c) DCT-12, (d) DCT-04T.

参考文献

[1]	J. Yang, S.K.Putatunda, Mater. Sci. Eng. A, 382(2004), pp. 265-279
[2]	S. ?oli?, M. Godec, Z. Schauperl, ?. Schauperl, Metall Mater. Trans. A, 47(2016), pp. 5058-5070
[3]	S. Putatunda, C. Martis, R. Papp, F. Diekman,Proceedings of the 26th ASM Heat Treating Society Conference,(2011), pp. 44-49
[4]	J. Yang, S.K.Putatunda, Mater. Sci. Eng. A, 406(2005), pp. 217-228
[5]	S.K. Putatunda, S. Kesani, R. Tackett, G. Lawes, Mater. Sci. Eng. A,435-436(2006), pp. 112-122
[6]	F.V.GuerraL, A. Bedolla-Jacuinde, I. Mejía, J. Zuno, C. Maldonado, Mater. Sci. Eng. A, 648(2015), pp. 193-201
[7]	W.F. Smith,Structure and Properties of Engineering Alloys,(2nd ed.), McGraw-Hill, New York (1993)
[8]	J.J. Cui, H.Y. Zhang, L.Q. Chen, H.Z. Li, W.P.Tong, Acta Metall. Sin.(Engl. Lett.), 27(2014), pp. 476-482
[9]	Y.L. Bai, Y.K. Luan, N.N. Song, X.H. Kang, D.Z. Li, Y.Y.Li, J. Mater. Sci. Technol., 28(2012), pp. 853-858
[10]	J.J. Cui, L.Q.Chen, Metall. Mater. Trans. A, 46(2015), pp. 3627-3634
[11]	S. Zhirafar, A. Rezaeian, M. Pugh, J. Mater. Process. Technol., 186(2007), pp. 298-303
[12]	A. Bensely, A. Prabhakaran, D. MohanLal, G. Nagarajan, Cryogenics, 45(2006), pp. 747-754
[13]	P. Baldissera, C. Delprete, Mater. Des., 30(2009), pp. 1435-1440
[14]	K. Vadivel, R. Rudramoorthy, Int. J. Adv. Manuf. Technol., 42(2009), pp. 222-232
[15]	A. Akhbarizadeh, A. Shafyei, M.A.Golozar, Mater. Des., 30(2009), pp. 3259-3264
[16]	V. Firouzdor, E. Nejati, F. Khomamizadeh, J. Mater. Process. Technol., 206(2008), pp. 467-472
[17]	S. ?oli?, F. Cajner, P. Panjan, Materialwiss. Werkstofftech., 44 (12) (2013), pp. 950-958
[18]	S. ?oli?, F. Cajner, V. Leskov?ek, M.P.Mat, Test, 10(2012), pp. 688-693
[19]	D. Das, A.K. Dutta, K.K.Ray, Wear, 266(2009), pp. 297-309
[20]	K. Amini, A. Akhbarizadeh, S. Javadpour, Vacuum, 86(2012), pp. 1534-1540
[21]	L.Q. Chen, J.J. Cui, W.P. Tong, MATEC Web Conf., 21 (08008) (2015), pp. 1-7
[22]	B.D. Cullity,Elements of X-ray Diffraction,Addison-Wesley, Reading MA (1974), pp. 391-395
[23]	O. Eri?, D. Rajnovi?, S. Zec, L. Sidjanin, M.T.Jovanovi?, Mater. Character., 57(2006), pp. 212-218
[24]	J. Wang, J. Xiong, H.Y. Fan, H.S. Yang, H.H. Liu, B.L.Shen, J. Mater. Process. Technol., 209(2009), pp. 3236-3246
[25]	H.S. Yang, J. Wang, B.L. Shen, H.H. Liu, S.J. Gao, S.J.Huang, Wear, 261(2006), pp. 1150-1154
[26]	P. Baldissera, D. Delprete, J. Open Mech. Eng., 2(2008), pp. 1-11
[27]	A.I. Tyshchenko, W. Theisen, A. Oppenkowski, Mater. Sci. Eng. A, 527(2010), pp. 7027-7039
[28]	D. Thakur, B. Ramamoorthy, L. Vijayaraghavan, Mater. Lett., 62(2008), pp. 4403-4406
[29]	X.J. Xu, W. Xu, F.H. Ederveen, S. van der Zwaag, Wear, 301(2013), pp. 89-93
[30]	B. Narayanaswamy, P. Hodgson, H. Beladi, Wear,350-351(2016), pp. 155-165
[31]	J.J. Cui, L.Q. Chen, H.Z. Li, W.P.Tong, Acta Metall. Sin., 53(2016), pp. 778-786,(in Chinese)

Microstructure and abrasive wear resistance of an alloyed ductile iron subjected to deep cryogenic and austempering treatments

RichHTML

可视化

摘要/Abstract

引用本文

使用本文

图/表 10

参考文献

相关文章 0

编辑推荐

Metrics

本文评价