Anisotropic corrosion resistance of TiC reinforced Ni-based composites fabricated by selective laser melting

doi:10.1016/j.jmst.2018.12.020

材料科学与技术 ›› 2019, Vol. 35 ›› Issue (6): 1128-1136.DOI: 10.1016/j.jmst.2018.12.020

收稿日期:2018-08-21 修回日期:2018-10-31 接受日期:2018-12-23 出版日期:2019-06-20 发布日期:2019-06-19

Anisotropic corrosion resistance of TiC reinforced Ni-based composites fabricated by selective laser melting

Hongmei Zhang^a^b, Dongdong Gu^a^b^*(), Lixia Xi^a^b, Han Zhang^a^b, Mujian Xia^a^b, Chenglong Ma^a^b

^aCollege of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
^bJiangsu Provincial Engineering Laboratory for Laser Additive Manufacturing of High-Performance Metallic Components, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Received:2018-08-21 Revised:2018-10-31 Accepted:2018-12-23 Online:2019-06-20 Published:2019-06-19
Contact: Gu Dongdong
About author:
¹ These authors contributed equally to this work.

摘要/Abstract

Abstract:

Electrochemical measurements on three planes of TiC/Inconel 718 composites fabricated by selective laser melting (SLM) were performed to study the corrosion property. The results showed that the YZ-plane with dense and fine columnar structures possessed high microhardness and superior corrosion resistance in 3.5 wt% NaCl solution. For the XZ-plane, a decreased anti-corrosion property was observed owing to its inhomogeneous microstructures. While the XY-plane with large irregular pores and clustered ring-like structures was more susceptible to corrosion compared with the other two planes. Comparative analysis suggested that the anisotropic corrosion behaviors were significantly dependent on the surface defects, microstructure characteristics and added reinforcements.

Key words: Selective laser melting, Corrosion resistance, Nickel based composite, Microstructure

. [J]. 材料科学与技术, 2019, 35(6): 1128-1136.

Hongmei Zhang, Dongdong Gu, Lixia Xi, Han Zhang, Mujian Xia, Chenglong Ma. Anisotropic corrosion resistance of TiC reinforced Ni-based composites fabricated by selective laser melting[J]. J. Mater. Sci. Technol., 2019, 35(6): 1128-1136.

图/表 13

Fig. 1. Three-dimensional diagram of SLM-processed Ni-based composite sample and three different studied planes.

Table 1 The chemical compositions of 20 wt% TiC/Inconel 718 composites.

Element	Fe	Cr	Nb	Mo	Ti	C	Al	O	Ni
wt.%	17.44	19.32	5.12	3.99	2.99	3.66	0.67	0.63	Balance

Fig. 2. 3D optical metallographic images of (a) polished surface and (b) etched surface of SLM-processed composites at three different planes.

Fig. 3. SEM images showing microstructures of etched SLM-processed composites: (a, b) YZ-plane, (c, d) XZ-plane, (e, f) XY-plane.

Fig. 4. (a) Histogram plot displaying distribution of pore diameters on the three planes, Hardness profile on the three planes of SLM-processed composites: (b) XY-plane, (c) XZ-plane, (d) YZ-plane.

Fig. 5. Potentiodynamic polarization curves for the XY-, XZ- and YZ-planes of SLM-processed composites in 3.5 wt% NaCl solution. The inserted was potentiodynamic polarization curves of Inconel 718 alloy.

Table 2 Electrochemical parameters of the polarization curves for three planes of SLM-processed composites.

SLM-ed Planes	E_corr (mV vs SCE)	I_corr (A cm^-2)
XY	-302 ± 15	(3.37 ± 0.17)×10^-5
XZ	-264 ± 13	(2.99 ± 0.15)×10^-5
YZ	-221 ± 10	(4.03 ± 0.20)×10^-7

Fig. 6. EIS measurements for the XY-, XZ- and YZ-planes of SLM-processed composites in 3.5 wt% NaCl solution: (a) Nyquist plots, (b) Bode plots. The inserted figure in (a) was an equivalent circuit.

Table 3 Equivalent circuit parameters for three planes of composites in 3.5 wt% NaCl solution.

SLM-ed Planes	Rs (Ω cm²)	CPE₁,Y₀ (×10^-5 S sⁿ cm^-2)	n₁	R_f (kΩ cm²)	CPE₂,Y₀ (×10^-5 S sⁿ cm^-2)	n₂	R_ct (kΩ cm²)	χ² (×10^-3)
XY	7.88 ± 0.39	16.58 ± 0.82	0.67 ± 0.03	2.91 ± 0.15	10.80 ± 0.54	0.68 ± 0.03	39.68 ± 1.98	2.28 ± 0.11
XZ	7.51 ± 0.37	10.92 ± 0.55	0.73 ± 0.04	3.42 ± 0.17	18.80 ± 0.94	0.73 ± 0.02	96.23 ± 4.81	2.02 ± 0.10
YZ	7.43 ± 0.35	4.39 ± 0.22	0.75 ± 0.01	16.22 ± 0.81	4.43 ± 0.22	0.75 ± 0.04	169.60 ± 6.48	2.38 ± 0.12

Fig. 7. (a) Nyquist plots, (b) Bode plots of polished Inconel 718, (c, d) SEM images of surface morphology of Inconel 718 after electrochemical test in 3.5 wt% NaCl solution.

Fig. 8. (a) The corrosion rate of the YZ-plane immersed in 3.5 wt% NaCl solution, (b) Potentiodynamic curve, (c) Nyquist plot, (d) Bode plots after the YZ-plane immersed in 3.5 wt% NaCl solution for 100 h.

Fig. 9. Fitted XPS spectra of (a) Cr 2p, (b) Ni 2p3/2, (c) Fe 2p3/2 and (d) Mo 3d obtained for the YZ-plane after electrochemical tests.

Fig. 10. Schematic diagram of corrosion mechanism of SLM-processed TiC/Inconel 718 composites.

参考文献

[1]	D.D. Gu, W. Meiners, K. Wissenbach, R. Poprawe, Int. Mater. Rev. 57 (2012) 133-164.
[2]	S. Li, Q.S. Wei, Y.S. Shi, Z.C. Zhu, D.Q. Zhang, J. Mater. Sci. Technol. 31 (2015) 946-952.
[3]	Y.L. Guo, L.N. Jia, B. Kong, Y.L. Huang, H. Zhang, Acta Metall. Sin.(Engl. Lett.), 31 (2018) 477-486.
[4]	R. Casati, J. Lemke, M. Vedani, J. Mater. Sci. Technol. 32 (2016) 738-744.
[5]	S. Bagherifard, N. Beretta, S. Monti, M. Riccio, M. Bandini, M. Guagliano, Mater. Des. 145 (2018) 28-41.
[6]	P. Kumar, O. Prakash, U. Ramamurty, Acta Mater. 154 (2018) 246-260.
[7]	H.Y. Wan, Z.J. Zhou, C.P. Li, G.F. Chen, G.P. Zhang, J. Mater. Sci. Technol. 34 (2018) 1799-1804.
[8]	I.T. Ho, Y.T. Chen, A.C. Yeh, C.P. Chen, K.K. Jen, Addit. Manuf. 21 (2018) 465-471.
[9]	D.G. Ahn, K.W. Byun, M.C. Kang, J. Mater. Sci. Technol. 26 (2010) 362-366.
[10]	P. Páramo-Ka?etas, U. ?zturk, J. Calvo, J.M. Cabrera, M. Guerrero-Mata, J. Mater. Process. Technol. 255 (2018) 204-211.
[11]	Q. Mao, Q.Q. Yang, W.H. Xiong, S.T. Li, M. Zhang, L.J. Ruan, Ceram. Int. 44 (2018) 13303-13312.
[12]	C.K. Sahoo, M. Masanta, J. Mater. Process. Technol. 240 (2017) 126-137.
[13]	B. Song, Z.W. Wang, Q. Yan, Y.J. Zhang, J.L. Zhang, C. Cai, Q.S. Wei, Y.S. Shi, Mater. Sci. Eng. A 707 (2017) 478-487.
[14]	Y.J. Zhang, J.L. Zhang, Q. Yan, L. Zhang, M. Wang, B. Song, Y.S. Shi, Scr. Mater. 148 (2018) 20-23.
[15]	Y.C. Wang, J. Shi, S.Q. Lu, Y. Wang, J. Manuf. Sci. Eng.-Trans. ASME, 139 (2017), Article 041005.
[16]	T. Rong, D.D. Gu, Q.M. Shi, S.N. Cao, M.J. Xia, Surf. Coat. Technol. 307 (2016) 418-427.
[17]	N. Dai, L.C. Zhang, J.X. Zhang, Q.M. Chen, M.L. Wu, Corros. Sci. 111 (2016) 703-710.
[18]	Y. Chen, J.X. Zhang, X.H. Gu, N.W. Dai, P. Qin, L.C. Zhang, J. Alloys. Compd. 747 (2018) 648-658.
[19]	D.D. Gu, C.L. Ma, M.J. Xia, D.H. Dai, Q.M. Shi, Engineering 3 (2017) 675-684.
[20]	D.H. Dai, D.D. Gu, H. Zhang, J.P. Xiong, C.L. Ma, C. Hong, R. Poprawe, Opt. Laser Technol. 99 (2018) 91-100.
[21]	P.F. Guo, X. Lin, W.D. Huang, J. Appl. Electrochem. 47 (2017) 1083-1090.
[22]	W. Liu, H.P. Xiong, N. Li, S.Q. Guo, R.Y. Qin, Acta Metall. Sin.(Engl. Lett.), 31 (2018) 362-370.
[23]	S.F. Zhou, Y.J. Huang, X.Y. Zeng, Q.W. Hu, Mater. Sci. Eng. A 480 (2008) 564-572.
[24]	B.J. Wang, D.K. Xu, J.H. Dong, W. Ke, J. Mater. Sci. Technol. 34 (2018) 1756-1764.
[25]	A.M. Fekry, Electrochim. Acta 54 (2009) 3480-3489.
[26]	F.F. Yang, H.J. Kang, E.Y. Guo, E.R.G. Li, Z.N. Chen, Y.H. Zeng, T.M. Wang, Corros. Sci. 139 (2018) 333-345.
[27]	Z.B. Qin, Z. Wu, X.S. Zen, Q. Luo, L. Liu, W.J. Lu, W.B. Hu, Corrosion 72 (2016) 1269-1280.
[28]	A. Kocijan, D.K. Merl, M. Jenko, Corros. Sci. 53 (2011) 776-783.
[29]	L. Tan, X. Ren, K. Sridharan, T.R. Allen, Corros. Sci. 50 (2008) 3056-3062.
[30]	J.B. Lei, C. Shi, S.F. Zhou, Z.J. Gu, L.C. Zhang, Surf. Coat. Technol. 334 (2018) 274-285.
[31]	R.F. Schaller, J.M. Taylor, J. Rodelas, E.J. Schindelholz, Corrosion 73 (2017) 796-807.
[32]	D.C. Kong, X.Q. Ni, C.F. Dong, L. Zhang, C. Man, J.Z. Yao, K. Xiao, X.G. Li, Electrochim. Acta 276 (2018) 293-303.
[33]	L. Luo, X. Shan, Z.H. Zou, Z.C.S. Zhao, X. Wang, A.P. Zhang, X.F. Zhao, F.W. Guo, P. Xiao, Corros. Sci. 126 (2017) 356-365.
[34]	L. Liu, Y. Li, F.H. Wang, Electrochim. Acta 53 (2008) 2453-2462.
[35]	P. Qin, Y.J. Liu, T.B. Sercombe, Y.H. Li, C.W. Zhang, C.Q. Cao, H.Q. Sun, L.C. Zhang, ACS Biomater. Sci. Eng. 4 (2018) 2633-2642.

Anisotropic corrosion resistance of TiC reinforced Ni-based composites fabricated by selective laser melting

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

图/表 13

参考文献

相关文章 0

编辑推荐

Metrics

本文评价